Useful things to know about this technique:
When colouring your paste- and you can colour white or Translucent- you can use a variety of mediums. Inkpads, reinkers and acrylic paints all work fine, and subtler shades can be achieved with mica powders. You can also add mica powders along with your inks/paints, for a pearly sheen. You can also add glitter, for sparkle that doesn't shed!
One thing to remember when using liquid colours to colour your paste is that the liquid will alter the consistency of the paste, so this is one case where you do not want to start with a little, and add till you've got the colour required. Acrylic paint will not be too bad, as it's not so liquid as ink, but with reinkers especially, go for a fairly dark colour, just adding a drop or two. You can always add a little more paste if you want to lighten it.Remember also, when adding to white paste it will lighten the colour anyway, and it will usually dry slightly lighter as well. Also, don't skimp on mixing up your custom colours. If you run out before finishing, you'll never mix exactly the same shade!Any leftover paste can be stored in small screwtop pots, and will last for a few months. If there is not enough to make that worthwhile, you can spread the excess onto a scrap of cardstock, using that to add all your waste paste to. Then, when dry, just cover with a sheet of hot foil, run through your laminator or foiling machine-you can even just iron it on- and you have a sheet of foiled card you can die cut sentiments from.Use a fairly good thick cardstock to work on, as the moisture from the paste will cause thinner cardstock to buckle.
Here are some I've done in the past.
Also, Mylar stencils such as these are not going to lay as totally flat on your cardstock as metal ones, so more care needs to be taken when adding paste, so that it doesn't start to seep under the edges of the design. Try to add enough paste, and use a wide enough spreader to cover the design in one sweep. Too many spreading motions will increase the likelihood of the paste going under the lines. Sweet Poppy have a fab wide spreader for this, and Lucy Ellis of Sweet Poppy has some cool videos on You Tube showing how to get the best results.
Finally- cleaning your stencils. You want to do this as quickly as possible, and I take a sandwich box with warm soapy water in up to my craft room to drop them in, to save going up and downstairs to a sink every time I've used a stencil. Make sure you have a bowl/tub large enough to lay the stencils flat in. Keeping them flat while washing & drying is really critical to keeping them in good condition. The paste comes off easily if you do it straight away. I have found that the Cosmic Shimmer glitter pastes are really difficult to remove if they start to dry on your stencil,so speedily dropping into water is important. I have an old towel on a work surface, and stand the tub on that. A small nailbrush is ideal for removing the paste, then I lay it onto the towel, and PAT dry. That's important, especially if the stencil has unattached parts, like the Flourish one does. If you bend parts through rubbing, they will always let paste/ink etc seep under the design. This applies to metal ones with unattached parts too, not just Mylar.
So, back to the cards. The card bases are topfold, half A4 sheets, which end up as 5¾ x 4⅛. The cardstock I used for the stencilling was 6 x 4 so I had a little to trim down to tidy it up. I finally trimmed the panels to 5¾ x 3⅜.As the panels were narrower than my base card, I decided to die cut some borders, you could also use border punches, of course.
I made some choices from this set by Spellbinders, called Shapeabilities On The Edge. They are just a hair longer than my panels,but these dies are fully repeatable, so you can make a border as long as you need.
I chose pearl papers and cut the edges twice for each card, then split down the middle. The pink one, which was the second up from the bottom in the dies, actually gives you two for one- you could easily use the offcut as a border too.The pearl papers came from some paper blocks I bought years ago at the NEC, from a company called Craftwork Cards, who sadly no longer exist.They are really useful for borders, or for punching from.
The strips were attached to the back of each panel, along the edges, with dst, then trimmed down to fit.
All four done.
Now they just need mounting onto the card fronts, and again I used DST for this. Remember to add tape to all 4 sides, as there will always be a little warping of the cardstock from the paste. If you are a wet glue user, I'd recommend laying them down with a weight on top for half an hour or so.
Now to add a sentiment, and I chose to use these Crealies Text dies for the baby cards. They are a small die, but the perfect size for these cards. there is quite a selection of sentiments available too. The 'A New Baby' sentiment is one die, but the three words are all separate, which I love as that gives you freedom of placement. I cut the die 4 times from white scrap card, then once each from the pink & blue pearl paper I used for the borders. This was so I could layer up the white die cuts twice, then add the
I have some stitched banner dies, from Aliexpress, and used the smallest size from the long set for this. It was actually a little longer than I wanted, but the bottom set was a little too short. I sorted that by just replacing the banner in the die, matching up the stitched lines, then trimming it shorter.
I decided the banners needed a little something else, so added an acrylic heart to each. I used a clear one for the blue card, as the only blue hearts I had were not close enough in colour to the blue used in the card.
For the wedding cards, I used the same banner die, but added the sentiment with peel offs, as there currently isn't a wedding die in the Crealies line. I have emailed to ask her about the possibility,though. 😀 A small white half pearl was added with some Glossy Accents.
No comments:
Post a Comment