You will need:
Next find a stamp to stamp into the top layer with. Any swirl/flourish/text stamp is perfect.
Finally, you need your embossing powders. UTEE (Ultra Thick Embossing Enamel) is the ideal choice, however you can still do this using ordinary embossing powder, you will just need more layers, and to be careful with the heating process as the finer grained powder will have a tendency to blow away. To avoid this, start heating from further away and bring your heat gun closer as you see the powder begin to melt.I first started off using ordinary powder, but loved what you could create with this technique, so I bought UTEE, and I got mine from ebay, which came in a plastic bag, and was MUCH cheaper than buying a branded name.Then you need a colour, and on this I have used Heat It Up's 'Blue Glass'.
If your heart cools too much for the EP or UTEE to stick to it for any reason, you have a couple of ways to put things right. Either re-heat the heart until the layers soften, or dab over it with the embossing pad and then continue.
WORDS OF WARNING: Embossing powder, especially UTEE, gets EXTREMELY HOT- don't get it on your fingers (Yes, I learnt the hard way, lol). Now I have two pieces of paper, one I tip the powder onto the piece on, then lift the piece with my scalpel and slip it onto the other piece to heat. Tip your excess powder back into its tub,then you have two empty sheets again to continue the process.
Now sprinkle on your first layer of UTEE, the ink should be plenty wet enough to hold the powder.
Now heat the powder/UTEE until it melts- it will look a bit uneven on this first coat, as you can see here.
Repeat this process three of four times if you are using UTEE. If you are using normal fine embossing powder, you may need 8 or 10 layers- just stop when it looks thick enough.
When you have completed your clear layers, you are ready to add the last, coloured layer.Sprinkle your coloured powder into the still melted UTEE, and carefully tip away the excess powder. Heat with your heat gun.
Your heart should look like this. If you are going to stamp a texture into it, you need to do this whilst the UTEE is still molten. Just press your stamp into the UTEE, don't worry, it does not harm your stamp!, as long as you have either Pigment ink, Staz-on or Versamark ink on your stamp.The ink coats the rubber, and helps to release it from the UTEE. Use Versamark/clear embossing ink if you just want texture, or want to rub some colour into it after, Staz-on if you want a dark imprint against a pale embossing, or a Pigment ink if you want a metallic finish, such as gold or silver.
|Your textured Heart.|
At this point, I remembered a technique I had seen in Julia Andrus' book, Paper Transformed, where she added Perfect Pearls before reheating to get 'trails' of mica seeming to fall down into the UTEE.The link takes you to the post. So I repeated the above process, until I reached the stage where you add the coloured powder.
What I did now was to sprinkle on my Blue embossing powder & tip off the excess, then I sprinkled a very small amount of Cosmic Shimmer Mica powder on the top, using the little brush that came with it.
This is how it looked as the powder started to melt, and the heat gun blew the mica across the surface slightly.
It looks a little heavy here,to be honest, and I thought I had overdone it.
You can see the heating has left the surface a little bubbled.
So, I let it cool a while, then patted it over with the clear embossing pad and sprinkled on another layer of UTEE.
This is what appeared from beneath the melting powder:
Well I hope this little how to has been of help-if anyone has a question, feel free to e-mail me from the link in my sidebar, and I'll try to help.By the way, I found the Blue Glass Embossing powder available Here,Here,Here and Here. I shall definitely be getting myself another couple of tubs of this :)